This article will demonstrates that how to configure the NetApp (Clustered ONTAP) two node cluster. Since I am going to use the simulator for this demonstration, we can’t virtualize the HA pair controllers. I will use two separate nodes to form the cluster with switch-less configuration(Assuming that direct cluster inter-connect cabling is done between nodes). In an order to form the cluster , we need to create the cluster on first node and join the remaining nodes. We have to make sure that all the systems are in sync with NTP source to prevents CIFS and Kerberos failures.
Note: Both the controllers are booted in C-Mode.
Creating the cluster on the first node:
1.Login to the first controller using serial console or IP address if you have already configure the Node IP. In this case, I have connected the first node using serial port.
2. Login as admin with no password.
3. Once you have reached the node shell , execute command “cluster setup” .
::> cluster setup
4. You will get wizard like below. Enter “create” to create a new cluster.
Welcome to the cluster setup wizard.
You can enter the following commands at any time:
"help" or "?" - if you want to have a question clarified,
"back" - if you want to change previously answered questions, and
"exit" or "quit" - if you want to quit the cluster setup wizard.
Any changes you made before quitting will be saved.
You can return to cluster setup at any time by typing "cluster setup".
To accept a default or omit a question, do not enter a value.
Do you want to create a new cluster or join an existing cluster? {create, join}: create
5.When prompted about using the node as a single node cluster, reply no because this will be a
multi-node cluster.
Do you intend for this node to be used as a single node cluster? {yes, no} [no]:
no
6.Since its a simulator,We are going to accept the default. Enter yes to accept the default values for cluster network configuration.
System Defaults:
Private cluster network ports [e0a,e0b].
Cluster port MTU values will be set to 1500.
Cluster interface IP addresses will be automatically generated.
Do you want to use these defaults? {yes, no} [yes]: yes
7.Enter the cluster Name .
Step 1 of 5: Create a Cluster You can type "back", "exit", or "help" at any question. Enter the cluster name: NetUA
8. Enter the license key for the node.
Enter the cluster base license key: XXXXXXXXXXXXXXXXXXXXXXXXX Creating cluster NetUA Network set up .....
9. Just press “Enter” to continue if you don;t want to add additional license keys at this moment.
Step 2 of 5: Add Feature License Keys You can type "back", "exit", or "help" at any question. Enter an additional license key []:
10. Set the Cluster vServer admin password.
Step 3 of 5: Set Up a Vserver for Cluster Administration You can type "back", "exit", or "help" at any question. Enter the cluster administrator's (username "admin") password: Retype the password: New password must be at least 8 characters long. You can type "back", "exit", or "help" at any question. Enter the cluster administrator's (username "admin") password: Retype the password:
11.Enter the port and IP details for the cluster LIF.
Enter the cluster management interface port [e0c]: Enter the cluster management interface IP address: 192.168.0.101 Enter the cluster management interface netmask: 255.255.255.0 Enter the cluster management interface default gateway: 192.168.0.1 A cluster management interface on port e0c with IP address 192.168.0.101 has been created. You can use this address to connect to and manage the cluster.
12. Enter the DNS details and Name server IP.
Enter the DNS domain names: learn.netapp.local Enter the name server IP addresses: 192.168.0.11 DNS lookup for the admin Vserver will use the learn.netapp.local domain.
13. We will skip the SFO since simulator will not support this feature.
Step 4 of 5: Configure Storage Failover (SFO) You can type "back", "exit", or "help" at any question. SFO will not be enabled on a non-HA system.
14. Set the Node location.
Step 5 of 5: Set Up the Node You can type "back", "exit", or "help" at any question. Where is the controller located []: BLR
15. Configure the node Management LIF.
Enter the node management interface port [e0f]: Enter the node management interface IP address: 192.168.0.91 Enter the node management interface netmask: 255.255.255.0 Enter the node management interface default gateway: 192.168.0.1 A node management interface on port e0f with IP address 192.168.0.91 has been created.
16. After configuring the node management LIF, it will automatically logoff.
Cluster setup is now complete. To begin storing and serving data on this cluster, log in to the command-line interface (for example, ssh admin@192.168.0.101) and complete the following additional tasks if they have not already been completed: - Join additional nodes to the cluster by running "cluster setup" on those nodes. - For HA configurations, verify that storage failover is enabled by running the "storage failover show" command. - Create a Vserver by running the "vserver setup" command. In addition to using the CLI to perform cluster management tasks, you can manage your cluster using OnCommand System Manager, which features a graphical user interface that simplifies many cluster management tasks. This software is available from the NetApp Support Site. Exiting the cluster setup wizard. Fri Nov 27 21:35:23 UTC 2015
17. Login back as admin with newly created password and check the cluster status.
login: admin Password: NetUA::> NetUA::> cluster show Node Health Eligibility --------------------- ------- ------------ NetUA-01 true true NetUA::>
We have successfully created new cluster using first controller .
Joining the second node on Cluster:
1.Login to the second controller using serial console or IP address if you have already configure the Node IP. In this case, I have connected the second node using serial port.
2. Login as admin with no password.
3. Once you have reached the node shell , execute command “cluster setup” .
::> cluster setup
4. You will wizard like below. Enter “join” to join with newly created cluster.
Welcome to the cluster setup wizard.
You can enter the following commands at any time:
"help" or "?" - if you want to have a question clarified,
"back" - if you want to change previously answered questions, and
"exit" or "quit" - if you want to quit the cluster setup wizard.
Any changes you made before quitting will be saved.
You can return to cluster setup at any time by typing "cluster setup".
To accept a default or omit a question, do not enter a value.
Do you want to create a new cluster or join an existing cluster? {create, join}: join
5. Accept the defaults and continue.
System Defaults:
Private cluster network ports [e0a,e0b].
Cluster port MTU values will be set to 1500.
Cluster interface IP addresses will be automatically generated.
Do you want to use these defaults? {yes, no} [yes]: yes
It can take several minutes to create cluster interfaces...
6.System will automatically scan using the cluster interconnect and it will provide the cluster name to join.
Step 1 of 3: Join an Existing Cluster You can type "back", "exit", or "help" at any question. Enter the name of the cluster you would like to join [NetUA]: NetUA Joining cluster NetUA Starting cluster support services .... This node has joined the cluster NetUA.
7. System will automatically skips the SFO.
Step 2 of 3: Configure Storage Failover (SFO) You can type "back", "exit", or "help" at any question. SFO will not be enabled on a non-HA system.
8. Configure the node management LIF.
Step 3 of 3: Set Up the Node You can type "back", "exit", or "help" at any question. Enter the node management interface port [e0f]: Enter the node management interface IP address: 192.168.0.92 Enter the node management interface netmask [255.255.255.0]: Enter the node management interface default gateway [192.168.0.1]: A node management interface on port e0f with IP address 192.168.0.92 has been created.
9. Once you have completed the node management LIF configuration, system will automatically logoff.
Cluster setup is now complete. To begin storing and serving data on this cluster, log in to the command-line interface (for example, ssh admin@192.168.0.101) and complete the following additional tasks if they have not already been completed: - Join additional nodes to the cluster by running "cluster setup" on those nodes. - For HA configurations, verify that storage failover is enabled by running the "storage failover show" command. - Create a Vserver by running the "vserver setup" command. In addition to using the CLI to perform cluster management tasks, you can manage your cluster using OnCommand System Manager, which features a graphical user interface that simplifies many cluster management tasks. This software is available from the NetApp Support Site. Exiting the cluster setup wizard. Fri Nov 27 21:43:52 UTC 2015 login:
10. Login to the node 2 using user “admin” and check the cluster status.
login: admin Password: NetUA::> cluster show Node Health Eligibility --------------------- ------- ------------ NetUA-01 true true NetUA-02 true true 2 entries were displayed. NetUA::>
11. Check the network configuration on Node2.
NetUA::> network interface show
Logical Status Network Current Current Is
Vserver Interface Admin/Oper Address/Mask Node Port Home
----------- ---------- ---------- ------------------ ------------- ------- ----
NetUA
cluster_mgmt up/up 192.168.0.101/24 NetUA-01 e0c true
NetUA-01
clus1 up/up 169.254.81.224/16 NetUA-01 e0a true
clus2 up/up 169.254.220.127/16 NetUA-01 e0b true
mgmt1 up/up 192.168.0.91/24 NetUA-01 e0f true
NetUA-02
clus1 up/up 169.254.124.94/16 NetUA-02 e0a true
clus2 up/up 169.254.244.74/16 NetUA-02 e0b true
mgmt1 up/up 192.168.0.92/24 NetUA-02 e0f true
7 entries were displayed.
NetUA::>
12. Check the network configuration on Node1.
NetUA::> network interface show
Logical Status Network Current Current Is
Vserver Interface Admin/Oper Address/Mask Node Port Home
----------- ---------- ---------- ------------------ ------------- ------- ----
NetUA
cluster_mgmt up/up 192.168.0.101/24 NetUA-01 e0c true
NetUA-01
clus1 up/up 169.254.81.224/16 NetUA-01 e0a true
clus2 up/up 169.254.220.127/16 NetUA-01 e0b true
mgmt1 up/up 192.168.0.91/24 NetUA-01 e0f true
NetUA-02
clus1 up/up 169.254.124.94/16 NetUA-02 e0a true
clus2 up/up 169.254.244.74/16 NetUA-02 e0b true
mgmt1 up/up 192.168.0.92/24 NetUA-02 e0f true
7 entries were displayed.
NetUA::>
We have successfully setup the two node NetApp cluster.
Hope this article is informative to you. Share it ! Comment it !! Be Sociable !!!
The post NetApp – Configuring the Two Node Cluster – Part 6 appeared first on UnixArena.